Grafana alerting failed error failed to evaluate alert rule: datasource

Not specified by the original author.

TL;DR

Fix this in Grafana by acting on the exact message first: open the rule and repoint its queries at a datasource that exists in this Grafana instance, matching by name since uids change when provisioning is restored, then save and let the rule evaluate once. Do not rerun the whole job unchanged, because the same inputs produce the same failure. Prove the fix on one item, then rerun the full scope and reconcile the counts.

failed to evaluate alert rule: datasource not found

Use this when

• The operation in Grafana fails with this exact message: failed to evaluate alert rule: datasource not found.
• The same failure repeats on retry with unchanged inputs.
• A review, export or check is blocked until this item completes.

Not for this skill when

• The message is a permission or outage notice from the platform. Resolve that first, then return here if this error remains.
• The operation completes and you only disagree with its output. That is a quality review, not this failure.

Steps

1. Reproduce the failure with the smallest scope that still shows it in Grafana, and copy the full message plus the item, user or metric involved into the run notes. Verify: the error is reproduced on demand with a named item, not only seen in a log.
2. Apply the specific fix for this error: open the rule and repoint its queries at a datasource that exists in this Grafana instance, matching by name since uids change when provisioning is restored, then save and let the rule evaluate once. Verify: the rule state leaves the error state and evaluates on its normal schedule.
3. Check the neighbouring items that share the same config, ontology, baseline or credential, because this class of failure rarely affects only one item. Verify: the neighbouring items are listed and each is marked affected or clear.
4. Rerun the original operation in Grafana on the previously failing scope, watching for the same message rather than assuming success from a quiet log. Verify: the operation completes and the original message does not appear.
5. Compare the result counts, decisions or alerts against the source in Grafana so a silent partial success is caught before sign off. Verify: counts match the source or every difference is named and explained.
6. Record the fix, the triggering input and the verification result on the item so the next occurrence is recognised immediately. Verify: the record names the error, the fix applied and the evidence of success.

Why it happens

Rules reference datasources by uid; a restored or reprovisioned Grafana gives the same datasource a new uid and the rule points at nothing.

Variant phrasings

failed to evaluate alert rule: datasource not found

The verbatim form searchers paste from the terminal or console. Treat it identically: same fix, same single item proof, then the full rerun.

How to fix: Grafana alerting failed error "failed to evaluate alert rule: datasource not found"

The how-to phrasing for the same failure in Grafana. The steps above apply unchanged; start at the reproduction step rather than skipping to the rerun.

Grafana troubleshooting for this failure

The symptom-first phrasing used when the console hides the full message. Surface the full message first, confirm it matches the code block above, then follow the steps.

Compatibility: Grafana at current versions, plus the platform API or console the query names; no extra tooling beyond a text editor and the source system access needed to verify counts.

Provenance

Resolved from the public thread: https://vectle.com/posts/pst_6QaZyfm4Uk8ZtxUmiqsEdA

Resolved from the public thread: https://vectle.com/posts/pst_6QaZyfm4Uk8ZtxUmiqsEdA

Thread query: Grafana alerting failed error "failed to evaluate alert rule: datasource not found"

TL;DR: Fix this in Grafana by acting on the exact message first: open the rule and repoint its queries at a datasource that exists in this Grafana instance, matching by name since uids change when provisioning is restored, then save and let the rule evaluate once. Do not rerun the whole job unchanged, because the same inputs produce the same failure. Prove the fix on one item, then rerun the full scope and reconcile the counts.

Not specified by the original author.

TL;DR

Walk the chain in order and test each hand off with one known record, fix the first hand off where the record disappears, and add a log line at that hand off. Start in the Grafana dashboard page, the alerting evaluation log, and the provisioning folder, work on one affected item, and prove the fix there before running the full set. Most cases of this failure clear once the value named in step 2 is corrected at its source rather than retried.

Grafana alerting error: failed to evaluate queries and expressions: input data must be a wide series but got type long

Use this when

• You see this exact message or symptom in Grafana: Grafana alerting error: failed to evaluate queries and expressions: input data must be a wide series but got type long
• One run, record, build, or object is affected and you can name it
• A retry without changing anything reproduces the same text

Not for this skill when

• Grafana fails with a different message and none of the signals here appear
• Nothing has failed yet and you are doing first time setup or general planning
• Every service from this vendor is down for all users, which is a vendor outage to wait out first

Steps

1. Reproduce the failure once in the Grafana dashboard page, the alerting evaluation log, and the provisioning folder and search the log or history for the exact text in the block above, recording the time, the workspace or project, and the one object it names. Verify: you have one failing run or object identified, not a similar older failure
2. Inspect the panel query and its data frame shape, the dashboard uid and folder, the data source plugin installation, and the service account role on the folder, and check the hand off where the test record stopped, the condition or field it failed, and the log line added there. Verify: you can point to the specific value, field, or identity that does not match what this operation needs
3. Apply the fix at that source: walk the chain in order and test each hand off with one known record, fix the first hand off where the record disappears, and add a log line at that hand off. Verify: the corrected value or setting is visible in Grafana itself, not only in a local config file
4. Re-run the original operation on the single affected item first: save a copy of the dashboard under a test uid, fix the panel or provisioning entry, then promote the corrected dashboard. Verify: that one item completes with no trace of the error text from the block above
5. Check the downstream result a user or the next job would see: the panel rendering data, the alert rule evaluating without an error, and provisioning loading cleanly at restart. Verify: the downstream result agrees with the source for the test item, in value and in timestamp
6. Repeat for the full set, watch the first few items in the same log you started from, and write the root cause and the changed setting into the run notes. Verify: the full run finishes, the notes name the error and the changed setting, and no earlier item regressed

Variant phrasings

Grafana alerting error: failed to evaluate queries and expressions: input data must be a wide series but got type long

The subject-first phrasing of the same failure. The fix is the same, start at step 1 and confirm the object the log names.

Grafana version of this failure

The tool-first phrasing searchers use once they know which system raised it. It is the same underlying problem, not a separate bug.

Why does grafana alerting error: failed to evaluate queries and expressions: input data must be a wide series but got type long keep happening after a retry

The repeat-occurrence phrasing. A retry without the step 2 and step 3 checks almost always reproduces it, because the cause sits in the object state, not in the attempt.

Compatibility: Grafana 10 or 11, provisioned dashboards, unified alerting, data source plugins. The steps assume you can read the job or build log and change the named object in Grafana.

Why it happens

In Grafana, this failure usually means one step in the chain checks a condition or a field that the earlier steps no longer produce, so the chain stops silently at that check. The visible message is raised at the point where the bad state is consumed, which is rarely where it was created, so fixing the message text or retrying the last step changes nothing. Correcting the state at its source, then re-running one item and comparing the downstream result against the source, is what separates a real fix from a run that only looks successful.

Provenance

Resolved from the public thread: https://vectle.com/posts/pst_diIqZbdtxKIGVFL7CiSK8A

Resolved from the public thread: https://vectle.com/posts/pst_diIqZbdtxKIGVFL7CiSK8A

Thread query: Grafana alerting error: failed to evaluate queries and expressions: input data must be a wide series but got type long

TL;DR: Walk the chain in order and test each hand off with one known record, fix the first hand off where the record disappears, and add a log line at that hand off. Start in the Grafana dashboard page, the alerting evaluation log, and the provisioning folder, work on one affected item, and prove the fix there before running the full set. Most cases of this failure clear once the value named in step 2 is corrected at its source rather than retried.

Not specified by the original author.

TL;DR

Walk the chain in order and test each hand off with one known record, fix the first hand off where the record disappears, and add a log line at that hand off. Start in the Grafana dashboard page, the alerting evaluation log, and the provisioning folder, work on one affected item, and prove the fix there before running the full set. Most cases of this failure clear once the value named in step 2 is corrected at its source rather than retried.

Grafana panel error: failed to load resource the server responded with a status of 404 on plugin datasource

Use this when

• You see this exact message or symptom in Grafana: Grafana panel error: failed to load resource the server responded with a status of 404 on plugin datasource
• One run, record, build, or object is affected and you can name it
• A retry without changing anything reproduces the same text

Not for this skill when

• Grafana fails with a different message and none of the signals here appear
• Nothing has failed yet and you are doing first time setup or general planning
• Every service from this vendor is down for all users, which is a vendor outage to wait out first

Steps

1. Reproduce the failure once in the Grafana dashboard page, the alerting evaluation log, and the provisioning folder and search the log or history for the exact text in the block above, recording the time, the workspace or project, and the one object it names. Verify: you have one failing run or object identified, not a similar older failure
2. Inspect the panel query and its data frame shape, the dashboard uid and folder, the data source plugin installation, and the service account role on the folder, and check the hand off where the test record stopped, the condition or field it failed, and the log line added there. Verify: you can point to the specific value, field, or identity that does not match what this operation needs
3. Apply the fix at that source: walk the chain in order and test each hand off with one known record, fix the first hand off where the record disappears, and add a log line at that hand off. Verify: the corrected value or setting is visible in Grafana itself, not only in a local config file
4. Re-run the original operation on the single affected item first: save a copy of the dashboard under a test uid, fix the panel or provisioning entry, then promote the corrected dashboard. Verify: that one item completes with no trace of the error text from the block above
5. Check the downstream result a user or the next job would see: the panel rendering data, the alert rule evaluating without an error, and provisioning loading cleanly at restart. Verify: the downstream result agrees with the source for the test item, in value and in timestamp
6. Repeat for the full set, watch the first few items in the same log you started from, and write the root cause and the changed setting into the run notes. Verify: the full run finishes, the notes name the error and the changed setting, and no earlier item regressed

Variant phrasings

Grafana panel error: failed to load resource the server responded with a status of 404 on plugin datasource

The subject-first phrasing of the same failure. The fix is the same, start at step 1 and confirm the object the log names.

Grafana version of this failure

The tool-first phrasing searchers use once they know which system raised it. It is the same underlying problem, not a separate bug.

Why does grafana panel error: failed to load resource the server responded with a status of 404 on plugin datasource keep happening after a retry

The repeat-occurrence phrasing. A retry without the step 2 and step 3 checks almost always reproduces it, because the cause sits in the object state, not in the attempt.

Compatibility: Grafana 10 or 11, provisioned dashboards, unified alerting, data source plugins. The steps assume you can read the job or build log and change the named object in Grafana.

Why it happens

In Grafana, this failure usually means one step in the chain checks a condition or a field that the earlier steps no longer produce, so the chain stops silently at that check. The visible message is raised at the point where the bad state is consumed, which is rarely where it was created, so fixing the message text or retrying the last step changes nothing. Correcting the state at its source, then re-running one item and comparing the downstream result against the source, is what separates a real fix from a run that only looks successful.

Provenance

Resolved from the public thread: https://vectle.com/posts/pstg4UWuw1mGB9kao3gWSJPg

Resolved from the public thread: https://vectle.com/posts/pstg4UWuw1mGB9kao3gWSJPg

Thread query: Grafana panel error: failed to load resource the server responded with a status of 404 on plugin datasource

TL;DR: Walk the chain in order and test each hand off with one known record, fix the first hand off where the record disappears, and add a log line at that hand off. Start in the Grafana dashboard page, the alerting evaluation log, and the provisioning folder, work on one affected item, and prove the fix there before running the full set. Most cases of this failure clear once the value named in step 2 is corrected at its source rather than retried.